The XHHV512-12L low voltage pulse generator is a tie-rod portable integrated device, which is mainly used for shock discharge during low-voltage cable fault testing. The pulse generator adopts humanized design operation mode, high-precision dedicated high-voltage electronic components and high-frequency high-voltage technology, which is easy to operate, light in weight and easy to carry.
It integrates the energy storage capacitor, DC high voltage source, and discharge ball gap. The operation of this equipment is safe and reliable, with automatic protection functions of over-current, overvoltage and overheating, it can truly achieve the effect of not being damaged by impact, and it can also work normally with high voltage to ground.
The XHHV512-12L Low voltage pulse generator is equipped with a time relay, and the discharge time interval can be arbitrarily set within 0-100 seconds. When working, the high-voltage pulse output is uniform and controllable, high-voltage side voltage measurement, make the result real-time and accurate. Unique high-voltage measurement design, in the stop state, the voltmeter can indicate the capacitor voltage in real time. The user can observe the residual voltage while discharging, until the voltage value returns to zero, and finally make the discharge more thorough.
★ With over-current, over-voltage, over-heat automatic protection function;
★ With DC withstand voltage, impact discharge function;
★ Uniform and controllable high-voltage pulse output;
★ Super short-circuit protection function, which can make the high-voltage output directly short-circuit to the ground;
★ It has dual 2.5-level pointer meter display for current and voltage, which is intuitive and clear, and the impact discharge process is clear at a glance;
★ High-voltage side voltage measurement, real-time and accurate;
★ With zero start protection, and potentiometer zero output function, safe and reliable;
★ Unique high-voltage measurement design, in the stopped state, the voltmeter can indicate the capacitor voltage in real time;
★ The discharge time can be arbitrarily set within an appropriate interval;
★ With emergency stop function, in case of emergency, cut off the high voltage output urgently. | XHHV512-12L | Portable 12kV high voltage surge generator with DC withstand voltage test funcation |
| Impact high voltage: | 0~12kV adjustable |
| High voltage partial pressure | voltage accuracy 2.5 |
| Built-in capacitor | 12μF |
| Discharge power | 0-864J |
| Output voltage polarity | negative polarity |
| Impact power | 250W@peak |
| Overcurrent protection | 8mA (more than 3 seconds) |
| Working power | AC 220V ± 10%, 50Hz ± 2Hz(60Hz) |
| Output voltage polarity | negative polarity |
| Over temperature protection | 65ºC |
| Weight | <30kg |
| Ambient temperature | -20~+60ºC |
| Volumn | 540L×300W×450H mm |
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Panel function description
1. Safety ground: The ground of the instrument shell must be reliably connected to the ground in order to prevent the instrument shell from being electrified or people getting an .
2. High-voltage ground: also known as high-voltage tail, it must be reliably grounded to prevent high-voltage leakage and discharge. Poor contact may result in failure to increase the voltage, high-voltage breakdown damage to internal components of the instrument, and safety accidents caused by internal leakage or discharge of the instrument.
3. Sampling place: The negative terminal of the pulse energy storage capacitor has a high voltage and must be reliably grounded. It is used for sampling when the waveform is sampled in the high-voltage flashover state of the cable fault tester. (Sampling without high-voltage flashover still requires reliable grounding).
4. Discharge button: press this button to make contact with the ball gap, and discharge manually. (The duration of each key press cannot exceed 1s).
5.High-voltage start button: When the light of the start button is on, it means that the voltage output is in the zero state. When the light is on, the start button is valid. If the light of the start button is not on after turning on the power switch, turn the voltage adjustment knob counterclockwise until the light is on. When the start button light is on, press this button to start the device and generate high voltage output.
6. High-voltage stop button: When the test is completed or abnormality occurs, press this button to cut off the high-voltage output, the high-voltage light goes out, and the internal discharge ball stops working. When the stop button is on, it means that there is high voltage output, and when it is off, it means that there is no high voltage output.
7. Over-current protection switch: press this button, the over-current protection is turned on, and this button pops up, and the over-current protection operates. Only when this button is pressed down, there is high voltage output. After the overcurrent protection is activated, it must be turned off to discharge.
8. Voltage adjustment: After turning on the device, you must first turn the knob counterclockwise to the bottom, press the start button and then adjust clockwise to increase the output high voltage from small to large, and adjust counterclockwise to decrease the output high voltage from large to small.
9. Power switch: "Gear 1" turns on the AC 220V power supply switch, and "Gear 0" turns off the system power.
10. Fuse socket: where the fuse of the AC 220V power supply system is installed.
11. Power socket: instrument working power supply, AC 220V connection port.
12. Time setting: set the discharge time interval.
13. Ammeter: indication of the current on the low voltage side.
14. Voltmeter: High voltage output voltage indicating kV meter.
15. High-voltage output (EMP): When impacting discharge, connect the high-voltage output line.
16. High voltage output (DC): When DC withstand voltage, connect the high voltage output line.Packing list
Application-Underground cable fault location, cable withstand voltage test
